收藏本站
Last Time Buy
Closest Alternative is AP5724WUG-7
ZXLD1101
APPLICATIONS
Programming the maximum LED current
The maximum LED current is programmed by adding a
single resistor in series with the LED chain. The current
is determined by the resistor value and feedback
voltage and is given by:
I LED = V FB /R1
where V FB =100mV
The table below gives recommended resistor values
for required LED currents:
Pulsed Dimming - Gated Mode
If a lower frequency of 1kHz or less is applied to the EN
pin, the device will be gated 'on' and 'off' at a duty cycle
(D) corresponding to that of the input signal. The
average output current is then given by:
I OUTavg ? 0.1D/R1
This mode may be preferred over dc current control if
the purest white output is required. However, note the
120 s nominal turn-off delay of the device, when using
the device in this mode.
LED Current
10mA
15mA
20mA
30mA
R1 Value
10
6.8
5
3.3
Dimming Control via a PWM signal on the EN pin
A Pulse Width Modulated (PWM) signal can be applied
to the EN pin in order to adjust the output current to a
value below the maximum LED current. Two modes of
adjustment are possible as described below.
True Analog Dimming - Filtered ‘DC’ mode
If a PWM signal of 10kHz or higher is applied to the EN
pin, the device will remain active when the EN pin is
low. However, the input to the internal low pass filter
will be switched alternately from V REF to ground, with a
duty cycle (D) corresponding to that of the PWM signal.
This will present a filtered dc voltage equal to the duty
cycle multiplied by V REF to the control loop and will
produce a dc output current lower than the maximum
set value. This current is given by:
I OUTdc = 0.1D/R1
This mode of adjustment minimizes flicker in the light
output and system noise.
ISSUE 4 - JULY 2004
SEMICONDUCTORS
8
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
ZXLD1320DCATC IC LED DRVR WHITE BCKLGT 14-TDFN
ZXLD1321DCATC IC LED DRVR WHITE BCKLGT 14-TDFN
ZXLD1322DCCTC IC LED DRIVR WHITE BCKLGT 14-DFN
ZXLD1350ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1352ET5TA IC LED DRIVER HIGH BRIGHT TSOT-5
ZXLD1356DACTC IC LED DRIVER WHITE BCKLGT 6-DFN
ZXLD1360ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
ZXLD1362ET5TA IC LED DRIVR WHITE BCKLGT TSOT-5
相关代理商/技术参数
ZXLD1320 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:Buck mode DC-DC converter for LED driving
ZXLD1320DCATC 功能描述:直流/直流开关转换器 DC-DC Buck Conv. 1.5A output RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
ZXLD1321 制造商:ZETEX 制造商全称:ZETEX 功能描述:Boost mode DC-DC converter for LED driving with 1A output and current control
ZXLD1321DCATC 功能描述:直流/直流开关转换器 DC-DC Boost Conv 1A output RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
ZXLD1322 制造商:DIODES 制造商全称:Diodes Incorporated 功能描述:BUCK/BOOST MODE DC-DC CONVERTER
ZXLD1322DCCTC 功能描述:直流/直流开关转换器 Buck-Boost DC-DC Con 0.7A output RoHS:否 制造商:STMicroelectronics 最大输入电压:4.5 V 开关频率:1.5 MHz 输出电压:4.6 V 输出电流:250 mA 输出端数量:2 最大工作温度:+ 85 C 安装风格:SMD/SMT
ZXLD1322DCCTC-CUT TAPE 制造商:DIODES 功能描述:ZXLD1322 Series 15 V 600 kHz 700 mA Buck/Boost Mode DC-DC Converter - DFN-14
ZXLD1322DCTC 制造商:ZETEX 制造商全称:ZETEX 功能描述:Buck/boost mode DC-DC converter for LED driving with 700mA output and current control